5354阅读
0回复

[分享]微波设计经验法则100条

大家进步

UID ：71967

注册：2011-01-23
登录：2020-09-05
发帖：136
等级：仿真二级

0楼发表于: 2011-01-30 17:30:23

Microwave rules of thumb
Updated February 2, 2010
The origin of the phrase "rule of thumb" is debatable; some say it was once a man's right to beat
his wife with a stick no wider in diameter than his thumb. Was this such a bad thing?
What we mean by a microwave rule-of-thumb could be an inexact but notable relationship of one
or more design parameters with performance, or it could just be an easy way to remember
something that other lesser people often mix up. Obviously, you must use some discretion when
you apply these rules, exact results can vary widely depending on influences you haven't
considered, such as the phase of the moon.
Microwave rules of thumb have been handed down to new-hires by microwave old farts for the
last century. We know there are a lot of O.F. out there, so please send in your favorite rule of
thumb and win a pocket knife (what O.F. could resist an offer like that?) We will acknowledge
your contribution here (unless you prefer to remain anonymous). Attention, humor-disabled
readers... any tired references to Murphy's law will never make it to this page, so please don't feel
the need to share any of this boring crap with us!
We will keep compiling microwave rules of thumb on this page, in no particular order, and we
don't guarantee that we will reorder the rules in the future. These rules are scattered about the web
site in appropriate places as well. We will try to cross reference this section with other parts of the
encyclopedia so you can learn more about any subject that you are interested in.
1. Keep your fat fingers out of expensive hybrid modules, or someone might break your thumb!
2. The minimum noise figure of a FET varies linearly with frequency, up until Fmax. This
related rule came from John, who also supplied a reference (thanks!) The minimum noise figure of
a BJT varies quadratically with frequency, up until Fmax.
This rule was quoted from Bahl, I. and Bhartia, P. 2003, Microwave Solid State Circuit Design, 2
Ed, John Wiley & Sons, New Jersey, p.377
3. The loss of a branchline coupler is reduced as the square-root of frequency, given that the
same substrate and metalization is used. This is one outcome of the skin depth effect.
4. Five skin depths of a good conductor will keep your losses to a minimum in microstrip.
5. If you are using copper boards with half-ounce or thicker copper, you don't have to worry
about skin depth problems unless you are working below 200 MHz.
6. Electromagnetic energy such as microwave radiation travels one foot in one nanosecond in
free space. In teflon-dielectric coax cables, it travels one foot in about 1.5 nanoseconds. In
waveguide, speed is a function of frequency due to dispersion.
7. The return loss of a circulator is very nearly equal to its isolation.
8. The third-order intercept point of an amplifier is generally 10 dB higher than its one-dB
compression point, when measured at the output. This corresponds to 9 dB higher when measured
at the input.
9. The isolation resistor on a quadrature coupler (such as a Lange) on the output of a power amp
should be able to handle 25% of the total power if you want the amplifier to still (sort of) work if
one amp blows up. Otherwise 10% of the total power for a tuned hybrid, or 5% of the power if the
entire amp is on a MMIC.
10. For a given switch-arm design, a SPDT switch will have 6 dB more isolation than a
comparable SPST switch, as long as the "through" arm of the switch is properly terminated.
11. For 1-mil gold wirebonds, inductance of the bond wire in nanohenries is roughly equal to its
length in millimeters... an advantage of the Metric System that was brought to our attention by a
French engineer named Yves (merci!) Let's restate this rule-of-thumb so that baseball fans can use
it: 1 mil of bond wire is equal to 25 pico-Henries of inductance, or 40 mils of bondwire is equal to
one nanohenry.
12. To be considered a "lumped element", no feature of a structure can exceed 1/10 of a
wavelength at the maximum frequency of its usage.
13. To be a useful substrate, the height of a microstrip board should never exceed 1/10 of a
wavelength at the maximum frequency of it usage. We've made a table for you on this subject!
14. How do you know what WR number a waveguide is just by looking at it? The WR number is
simply the dimension of the broad wall in mils, divided by 10.
15. A good way to remember which is the E-plane and which is the H-plane in rectangular
waveguide is when you bend it, bends in the E-plane are the "easy way", while bends in the
H-plane are the "hard way".
16. For silicon or SiGe, 110 degrees C is the maximum junction temperature for reliable
operation (1,000,000 hours is typical median time to failure criteria). With the exception of silicon
LDMOS, which can operate up to 175C for 800 years, according to Leonard who works for a
major LDMOS supplier (thanks!) GaAs FET (or HEMT) channel temperature should not exceed
150 C for long-term reliable operation. For gallium nitride HEMT (GaN), 175 C is a good rule for
maximum channel temperature.
17. In order to cutoff spurious modes, the width of a package should generally not exceed
one-half of a wavelength in free space at the maximum operating frequency.
18. For microstrip and stripline curved lines, use a minimum radius of three line widths at
X-band and below. At higher frequencies, use five line widths for minimum radius. Even better,
use an optimum miter instead of a curve!
19. The 10% to 90% rise time of a pulsed signal, in nanoseconds, will be approximately equal to
0.35 divided by the bandwidth of the network, in GHz.
20. If you are trying to effect an RF short circuit using a quarter-wave stub, use a low impedance
line, or better still, use a radial stub.
21. Due to constructive interference, the individual return loss of two identical mismatches is 6
dB better than the worst case observed return loss of the two mismatches measured together.
22. Two identical mismatches can be made to cancel each other by locating them approximately
one-quarter (or perhaps three-quarters) wavelength apart. This rule is often used in PIN diode
switch and limiter design. Note that shunt capacitive VSWRs require slightly less than
one-quarter-wavelength to cancel (thanks, Mike!), while shunt inductive mismatches require
slightly more.
23. Want to remember the correct order of Ku, K and Ka radar bands? K is the middle band
(18-27 GHz), while Ku-band is lower in frequency (think K-"under") and Ka-band is higher in
frequency (think K-"above").
24. A chip attenuator is good for at least 1/16 watt if it is mounted to a circuit card such as
Duroid or FR-4, 1/4 watt if mounted to metal with conductive epoxy, and 1/2 watt if it is attached
with solder to a metal heatsink.
25. For a ten dB pad (90% power dissipation), size the input resistor to handle 1/2 of the
maximum intended input power. For a 20 dB pad (99% power dissipation), size it for 80% of the
max input power. For higher attenuation values, size the input resistor for the full RF input power.
26. When designing "split-block" waveguide sections, tell your mechanical engineer that you
have to split the guide the hard way, in the H-plane. If you put a mechanical seam in the E-plane,
you are looking for trouble, because the guide needs to pass RF current through the seam, and
very high signal losses and VSWRs can result.
27. For N-way resistor power dividers, power is transferred as (1/N)^2. Compare this to a
lossless power divider, which transfers power at (1/N), and you see that resistive dividers are
extremely inefficient (and get worse and worse the more arms you add), but for some applications,
they offer a cheap, wide-band solution.
28. For an impedance-matched amplifier, the impedance match it sees on one port will not affect
the impedance match it provides on the opposite port, provided that its ratio of S21 to S12 is down
by at least 20 dB. Example: you are designing a receiver in which your mixer has a very bad
match at the IF port, say 3:1 VSWR, or -6 dB. The mixer is followed by a GaAs HBT amplifier,
where S21 (gain) is 23 dB, and S12 (reverse isolation) is -25 dB. You are in trouble, because the
"round trip" through the amp is only -2 dB, so your receiver IF output match will be only 2 dB
better than the 3:1 match of the mixer, or -8 dB.
29. The P1dB point of a mixer at its RF input is often about 6 dB less than its LO drive level.
We've seen references that show P1dB can be between -10 dB and 0 dB from the LO power level,
so consult your mixer's data sheet!
30. The gain temperature coefficient of a MESFET or PHEMT amplifier is often approximately
-0.007 dB/degree C/stage, if the gate bias voltage is fixed. Self-biased amplifiers have much lower
gain/temperature coefficients (less variation with temperature).
31. When it comes to capacitor materials, the ones with the highest dielectric (K) are most likely
to have the worst variation over temperature.
32. The physical length of a Lange coupler is approximately equal to one quarter-wavelength at
the center frequency on the host substrate. The combined width of the strips is comparable to the
width of a fifty-ohm line on the host substrate.
33. If you forget to build image rejection into your receiver design, you might be adding three dB
to your receiver's noise figure. Approximately 20 dB image rejection will all but eliminate image
noise foldover.
34. If you are 2d2/ or farther from an antenna, you are in the far-field.
35. Via-hole inductance: on 2-mil (50 micron) GaAs, Lvia is about 10 pico-henries. For four-mil
(100 um) GaAs, it is about 20 pico-Henries. Anyone have a ROT for alumina or PWB inductance?
36. When measuring high power with a microwave watt meter assemble your in-line attenuators
with three dB pad nearest to the power source, next six dB and so on. That way the power is
dissipated in a fashion to cause least heating of the pads. Thanks to Paul, retired USCG! And
always check the power rating of every component that you screw onto the output of a high-power
source! -UE
37. If your getting high SWRs in a system with a wattmeter (i.e. Bird directional wattmeter) and
your antenna and coax haven't had a lighting hit or physical damage, use a spectrum analyzer to
check the output of your transmitter. Maybe what your seeing is harmonics from a bad transmitter
not a bad coax or antenna. Also thanks to Paul, retired USCG
38. The group delay of a filter is nearly proportional to its order. Also, filter group delay is
inversely proportional to filter bandwidth (small percentage bandwidth filters have large group
delay. This "corollary" came from Chip but we haven't had time to test it out: The insertion loss at
the band edge of a filter is equal to the insertion loss at the band center times the ratio of the group
delay at the band edge to the group delay at the band center. (i.e., the insertion loss is proportional
to how long the signal is in the filter!)
39. The effective dielectric constant for CPW is merely the average of the dielectric constant of
the substrate, and that of free space. If you are using GaAs, Er=12.9, the effective dielectric
constant would be (12.9+1)/2=6.95.
40. The noise figure of a mixer is generally equal to the magnitude of its conversion loss, or
maybe just a little bit less. A mixer with -6 dB conversion loss may have a noise figure of 5.5 dB.
41. You should measure the return loss of a mixer's three ports at the recommended LO drive
level, or you will get ugly results.
42. For the best LO to IF isolation in a double-balanced mixer, always tap off the IF from the RF
balun, not the LO balun. You should get 20 dB better LO rejection this way.
43. When subscribing to trade journals, always give them a fake email address and phone number.
Otherwise they will be bugging constantly!
44. To compute wavelengths in free space in your head, remember that 30 divided by frequency
in GHz will give you wavelength in centimeters. Thus 10 GHz is 3 centimeters wavelength, and
30 GHz is one centimeter wavelength (the "break point" where millimeter wavelengths start).
45. The beam width of an antenna of fixed area is proportional to its wavelength. Thus a 40 GHz
signal can be focussed to one quarter of the beam width of a 10 GHz signal.
46. The coupled port on a microstrip or stripline directional coupler is closest to the input port
because it is a backward wave coupler. On a waveguide broadwall directional coupler, the coupled
port is closest to the output port because it is a forward wave coupler.
47. The antenna pattern for a horn antenna can be approximated as
P(dB)=-10x( / -10dB)^2
48. Doppler shift at X-band is approximately 30 Hertz for 1 mile per hour. If you are traveling at
60 miles per hour, your Doppler frequency on police X-band radar will be approximately 1800 Hz.
49. Let's call this a "proposed" rule of thumb, because we don't have any supporting data yet. For
finite groundplane microstrip, you'll need at least five times either the substrate height, or the
microstrip width, as your groundplane width, whichever is MORE.
50. The gain of a narrow-beam reflector antenna is approximately 27000/( 1 2), where 1 and
2 are the 3 dB (half-power) beamwidths in the principal planes, measured in degrees (not radians).
51. Electromagnetic radiation at frequencies higher than light (such as x-rays) can cause cell
damage (ionizing radiation). EM radiation below light (such as microwaves) don't damage cells,
they only cause heating (which can cause injury as well, but is easy to avoid because it causes
pain!)
This additional info came from John (thanks!)
I would like to add some important information pertaining to microwave rule of thumb 51.
Specifically the rule states that non-ionizing radiation injury is easy to avoid because the heat it
generates causes pain.
Exposure to microwave radiation at power levels below the pain threshold does cause heating in
the lens of the eye producing cataracts. Heating denatures proteins in the crystalline lens of the eye
(in the same way that heat turns egg whites white and opaque) faster than the lens can be cooled
by surrounding structures. The lens and cornea of the eye are especially vulnerable because they
contain no blood vessels that can carry away heat. The damage is accumulative and over time
degrades vision. High power levels will produce discomfort that includes irritation of the eye
however; levels of power well below the average person’s pain threshold will induce cataracts
over time. It should be noted that frequencies whose wavelength more closely match the size of
the eye (X-band freqs with wavelengths in the 2-4 centimeter range) are particularly dangerous.
Also, there has been some infomation in the news on terahertz waves, which are purported to
unzip DNA molecules. Stay tuned! - UE
52. When measuring S-parameters to get group delay, you should pick the frequency interval to
achieve about 10 degrees S21 phase difference between frequency points. Less than this will make
the measurement jumpy, greater than 10 degrees might mask some real problems in group delay
flatness. How do you know in advance what frequency interval to pick? Excuse us while we go
think up a formula for this...
53. If you divide the switch element Figure of Merit by 100 (FOM=(1/(2 RonxCoff)), you will
arrive at the highest frequency that the device can be made to perform as a switch. Thus MESFET
switches will work up to about 26 GHz, PHEMTs will work up to 40 GHz, and PIN diodes will
work up to 180 GHz.
54. When you are counting the number of squares in a meandering resistor to determine its value,
the squares at each bend should be counted as 1/2 square.
55. Switch isolation is often limited by package isolation. If you design a 60 dB switch, you
should think carefully about how to package it!
56. Linear passive devices have noise figure equal to their loss. Expressed in dB, the NF is equal
to -S21(dB). Something with one dB loss has one dB noise figure. But wait, as Gene points out,
there is more to consider! This statement is true only if the passive linear device is at room
temperature. You'd best analyze the problem using noise temperature.
57. If you have 20 dB gain in your LNA or receiver, the noise figure contribution of the
subsequent stage will be small (unless the noise figure of the next stage is horrendous!)
58. Twenty dB of image rejection is about all you need before you can neglect image noise
foldover. Worst case, image noise foldover can degrade receiver noise figure by 3 dB.
59. The minimum width for a stripline that is encased by metal on the edges is 5 times the line
width, in order for the impedance to calculate with the "normal" closed form equations.
60. The angular beam width of a parabolic reflector can be estimated from the diameter of the
dish and the frequency of operation as: angular beam width (degrees)=70 degrees/(D/lambda).
Corrected thnks to Vincenzo!
61. If you are so fed up with your job that you are going to quit, line up another one first, unless
you like clipping coupons. As a corollary, don't burn every bridge on your way out of town, you
never know when you might be desperate enough to come back!
62. For pure alumina ( R=9.8), the ratio of W/H for fifty-ohm microstrip is about 95%. That
means on ten mil (254 micron) alumina, the width for fifty ohm microstrip will be about 9.5 mils
(241 microns). On GaAs ( R=12.9), the W/H ratio for fifty ohms is about 75%. Therefore on four
mil (100 micron) GaAs, fifty ohm microstrip will have a width of about 3 mils (75 microns). On
PTFE-based soft board materials R=2.2), W/H to get fifty ohms is about 3. Remember these!
63. The accepted limits of operation for rectangular waveguide are (approximately) between
125% and 189% of the lower cutoff frequency. Thus for WR-90, the cut-off is 6.557 GHz, and the
accepted band of operation is 8.2 to 12.4 GHz.
64. There is considerable overlap between waveguide standards, you can almost always find two
types that will work at one frequency. In order to get the lowest loss, choose the waveguide that
has the largest dimensions.
65. For a given frequency, waveguide will give the lowest loss per unit length. Coax loss will be
about 10X higher (in dB). Transmission line loss on MMICs (microstrip or coplanar waveguide) is
about 10X worse than coax, or 100X that of waveguide (but the lengths of the transmission lines
are really small!) Stripline, depending on its geometry, usually will be slightly higher in loss than
coax.
66. This one came from Scott! The wavelength in air, measured inches, is 11.803 divided by the
frequency in GHz. Throw in that the wavelength in or on dielectric is the wavelength in air
divided by the square root of the effective (close to actual for low dielectrics) relative dielectric
constant.
67. Whenever you bend a transmission line, to model the length of the line you should simply
ignore the extra length that is added by the bend. We'll cover our butts by saying this is just an
approximation, if the effective length of a line is critical to the design success, you'd better
simulate it in Sonnet!
68. If you use a radius greater than three times the line width, you will have a transmission line
that is almost indistinguishable in impedance characteristics from a straight section. According to
Chip: radiused bends are a waste of valuable real estate. Stick with well compensated right angles.
69. Coax line impedance is not a strong function of the eccentricity of the center conductor. You
can be off by a full 50% and the impedance will decrease on the order of only 10%! And
remember, impedance can only decrease if the center conductor is off center, it will never increase!
Another suggestion of Chip: When designing a coaxial structure you will never end up perfectly
concentric. Therefore, always design coaxial structures with 3-6% higher impedance and you will
end up with a better match.
70. For coax and stripline 50 ohm transmission lines that employ PTFE dielectric (or any
dielectric material with dielectric constant=~2), the inductance per foot is approximately 70 nH,
and the capacitance per foot is about 30 pF.
71. The isolation of a Wilkinson is limited to 6 dB better that the return loss of the source match
at its common port.
72. The split port return loss of a Wilkinson is no better than the return loss that is seen by the
Wilkinson at its common port.
73. An acceptable voltage droop for a power amplifier during pulsed operation is 5%, which will
drop the power by a similar amount (5%, or about a quarter of a dB). So for a PHEMT amp
operating at 8 volts, you allow a voltage droop of 0.4 volts. Use this rule when you calculate
charge storage capacitance!
74. In order to use silicon as a substrate, you need resistivity at least 100 ohm-cm or the loss is
going to eat your lunch.
75. For microstrip, you can (approximately) cut metal losses in half by doubling the dielectric
thickness. For example, going from 10 mil to 20 mil alumina, or two-mil to four-mil GaAs.
76. Any microwave semiconductor house that doesn't invest in new technology, is going to go
out of business in the long run. By long run, we mean five years.
77. Anyone who designs complex microwave circuits and claims they don't use the optimization
function in their EDA software is one of these three things: a liar, an idiot, or a super-genius with
IQ 250. You pick which one, then accuse them when they bring this up at their next peer review!
78. When laying out the top layer of a microstrip board many of us do a ground fill. The question
is how close to get to the microstrip lines – especially since the ground fill function is automated
in many layout programs. The answer is to keep >3 line widths away. This insures minimal
additional loss and impact to line impedance. Contributed by Tom!
79. Different loss mechanisms have different behaviors over frequency. Metal loss is
proportional to square-root frequency. Dielectric loss is proportion to frequency. Dielectric
conduction loss is constant over frequency.
80. When considering the transmission line loss due to dielectric conductivity, if the resistivity of
the dielectric is greater than 10,000 Ohm-cm, forget it! That pretty much rules out all substrates
except silicon, which can be anywhere from 1 Ohm-cm (very lossy) to 10,000 Ohm-cm (very
expensive float-zone silicon). PTFE is 1E18 Ohm cm!
81. Let's just call this a proposed rule of thumb (your comments are appreciated!) A transmission
line (coax, microstrip CPW, stripline but NOT waveguide) can be considered low-loss if the loss
per wavelength is less than 0.1 dB. Waveguide will routinely be 10X better than this benchmark!
82. For stripline and microstrip, the attenuation factor always decreases when characteristic
impedance is reduced. It's almost proportional; if you can live with 25 ohm transmission lines
instead of 50 ohms, you can cut your losses nearly in half! This is a different result than coax,
which has a sweet spot on the attenuation/impedance curve (77 ohms for air coax, 52 ohms for
PTFE-filled).
83. This rule of thumb has its own page! You can electrically measure the approximate length of
a cable (or any long transmission line) by noting the frequency separation between the dips in
VSWR (S11) and doing some simple math.
84. This rule of thumb has nothing to do with microwaves. At some point in your career you
might be asked to assist in the task of boxing up a co-worker's stuff, either because he or she died
or otherwise became incapacitated. Here's the rule: if you happen to find a framed picture of a
woman (man) tucked into a desk drawer, and you don't know what the co-worker's spouse looks
like, just throw out the picture, maybe save the frame for yourself if it's a nice one. There's little
chance you are discarding a priceless one-of-a-kind artifact, but there's a good chance the picture
will be an unwelcome surprise to the co-worker's spouse (why would the picture be buried in a
drawer in the first place?) We speak from a near-miss experience a long time ago, when an alert
friend of the co-worker pulled the "that's not his wife!" photo from the box just as it was heading
to the shipping department!
85. Here's a freespace path loss rule of thumb, thanks to Stefan.
86. The typical isolation you can expect from a two channel receiver is on the order of 25 dB.
For dual-channel MMICs, expect no more than 30 dB.
87. This rule came from Cheryl... if you don't want to worry about the metal cover of a module
pulling the impedances of the microstrip circuits you designed, make sure it is at a minimium
height of of 5X the substrate thickness and 5X the maximum line width, whichever is more.
Thanks!
88. When a solid state amplifier is pulsed on for 100 microseconds or longer ("long" pulse), it
reaches a quasi-steady-state junction or channel temperature, so for thermal and reliability analysis,
this case can be considered the same as continuous wave. Under the same operating conditions, to
get any reliability benefits from pulsed operation you need to operate with pulses of 10 us or less
("short" pulse).
89. When calculating the peak power handling of a transmission line due to dielectric breakdown
(arcing), you need to derate by 6 dB for conditions where the network might see a very high
VSWR (like an accidental open or short). ]oB~8d

未注册仅能浏览部分内容，查看全部内容及附件请先登录或注册

发帖回复