[已解决]在计算的过程中有如下提示

1.     The following message from the master process (MYID= 0): (C60HbL  
WARNING 33193: Negative vertex coordinates found in the geometry, STL export will not be conformal to the standard, one might consider moving the geometry to make all coordinates positive u ioBId  
         See also message in the output file A1_MLFMM.out PNG!q}(c  
Checking the geometrical input data G !;
<#|a  
qcR"i+b  
2.    The following message from the master process (MYID= 0): G;yh$n<"  
WARNING  1663: Inhomogeneous segmentation for triangles y)D7!s  
         See also message in the output file  A1_MLFMM.out B,avI&7M;S  
   Checking the geometrical input data for triangles !F[^?:pK  
2Pic4Z  
+lED6]+%  
3.    The following message from the master process (MYID= 0): /><+[\q4LM  
NOTE    33242: For the FMM there is the possibility to save memory by switching to single precision (see EG card), this is normally recommended ';Ew-u  
          See also message in the output file  A1_MLFMM.out IHStN,QD  
第一个问题 我认为是有警告是有负向的面元 但是我差了半天也没有（并不排除我出错误的原因） x$;kA}gy  
第二个问题 是不是因为 .. Hl b%/&  
\%$z!]S>  

未注册仅能浏览部分内容，查看全部内容及附件请先 登录 或 注册

多看一下 PDF 手冊跟範例對你會有幫助....    P
|tNmv[;  
me+u"G9I;  
第一個問題 我認爲是有警告是有負向的面元 但是我差了半天也沒有（并不排除我出錯誤的原因） 0 H0U%x8  
--> 方向性... file A1_MLFMM.out...裡會告訴您是那個面。 \f-@L;8#  
m8,jVR  
第二個問題 是不是因爲最大的邊與最小邊的比值超過100所以顯示Inhomogeneous segmentation `P/87=h  
沒架構，思考方向有2：
qp{3I("_  
1. inhomogeneous dielectric bodies #\l#f8(l  
2.inhomogeneous meshing j^)=<+Q;=  
從字面看來應該是2 nJ2
910"<  
WARNING  1663: Inhomogeneous segmentation for triangles .See also message in the output file  A1_MLFMM.out S[5OTwa8L  
Examples of BQ card usage: ]MmFtdvE  
The BQ card can be used to create the mesh shown in Figure 13-6, or also for inhomogeneous E@J}(76VS  
meshing as shown in Figure 13-7. Ov~vK\  
Figure 13-6: Example of a BQ card from demo BQ1.pre oH"VrS 6  
Figure 13-7: Example of a BQ card with an inhomogeneous segmentation from demo BQ3.pre W!R7D%nX  
July 2008 FEKO User’s Manual - DESCRIPTION OF THE GEOMETRY CARDS 13-9 ,:6.Gi)|  
k!0vpps
 
第三個問題 用fMM會節省内存 這個怎麽設置呢？ ^O
rO&w|  
NOTE    33242: For the FMM there is the possibility to save memory by switching to single precision (see EG card), this is normally recommended m}32ovpw  
1. single precision (see EG card) -,qGEJ  
Solution accuracy: This parameter can be set to force FEKO to use single precision for the storage of some of the memory critical arrays. Single precision storage is the default behaviour, and as compared to double precision the memory requirement is then half. Using double precision is recommended when the FEKO kernel gives a warning to switch to double precision (this might happen for instance at low frequencies where an increased accuracy is required). <El!,UBq<  
2.  MLFMM 8'-E>+L   
21 Using the MLFMM for electrically large models A)80qx:  
Keywords: MLFMM, large model, Radar cross section, trihedral U7xKu75G1  
In this example we consider a single plane wave incident (from ϑ=60◦ and ϕ=0◦) on a 9WT{~PGj  
large trihedral. The size of the trihedral (13.5λ2 surface area) was chosen such that it f7?u`
"C  
can still be solved incore on a PC using 519 MByte of RAM. Larger examples show a W_bA.zT{  
proportionally larger resource saving by using the MLFMM, but the absolute increase in &~'^;hy=  
solution time makes such an example impractical for explanation purposes. This example Aj{G=AT  
is large enough to demonstrate the advantage of using the MLFMM. R q .2  
22 Antenna coupling on an electrically large object q"-+`;^7(-  
Keywords: electrically large, MLFMM, CFIE, coupling, antenna placement, RHu4cK!5  
S-parameters d04fj/B  
A Rooivalk helicopter mock-up model with 3 monopole antennas located near the front, `1i\8s&O6@  
middle and back of the model respectively. S-parameters (coupling) are computed between sp7#e%R\  
the 3 antennas over a frequency range.

FMM是他自己MLFMM自己改成的一种算法吧 而且用单精度会节省一半内存 那个反向面元还是不大好找 能不能再看看