[提问讨论]FLOEMC使用手册

谁有FLOEMC使用手册之类的东西发上来共享以下，光有那几个例子解决不了问题。还是有很多问题解决不了，特别是一些自己做的 .. )u=46EU_  
pebNE3`#  

未注册仅能浏览部分内容，查看全部内容及附件请先 登录 或 注册

可以查看到帮助.但是依然不解决问题. ,a\pdEPj  
自带的帮助,e文的.

FLO/EMC Attribute Types #ZPy&GIr  
The attribute types used to define the modeling objects are: l} UOg   
3bPF+(`J  
Material - describing the electromagnetic properties of a material yXL]uh#b  
Surface - surface finish (only needed if you intend to transfer the project later to FLOTHERM) . [5{  
Transients - defining the functions describing time-dependent variables. b+ J)  
Outputs - selecting the variables to be calculated over a region. 4O'X+dv^I  
Circuits - defining the electric circuits that wires belong to. J;cTEB  
EM Sources - describing the field strength for an electromagnetic source. e$y VV#  
Field Components - setting the electromagnetic field components at a monitor point. G9P)Y#WB  
For some modeling objects, such as fans, some attributes are attached as part of the geometry set-up using the object definition dialogs. But, for most attributes, you attach them as an independent action. 
d`&F  
{h *Pkn1  
Attribute and Library Trees cG~-OHU  
Attributes are defined and stored independently from the modeling objects they describe, so that the same single attribute specification may be applied to multiple objects. fS(IN~
 
s6J`i&uu  
Attributes are stored in two main library directories displayed in the Library Manager. I:G4i}mA  
-% Z?rn2  
mo- Y %  
tN:PWj5  
From either of these two areas the attribute specifications can be copied (attached) to a modeling object by dragging from the store area and dropping on the modeling object in the project data tree or using attachment dialogs. [p# }=&d  
Wf>scl`s  
Project Attributes Ff@Cs0R  
The attributes known to the current project, that is, those attributes created in or copied to the project, can be seen when you expand the Project Attributes nodes. In the figure below, you can see the ambient and source attributes defined for this project 5rx;?yvn  
ds"q1  
CN, oH4IU  
. Q`7.-di  
J)leRR&  
See "Creating Attributes" M;K%=l$NG  
x-HN]quhe  
Central Library 6!^&]4  
Expanding the Libraries node displays the central library folders used to transfer definitions across projects. The figure below shows the first few entries in the supplied FLOTHERM Material Library 1C'_I  
{@w!kl~8  
p2:>m\  
hIv8A_>@`  
See "Library Manager" for a full description of the Library panel.

3: Set Up an Emission Type Simulation 0;V "64U  
All the simulation settings (type of solution, frequency range of interest and maximum simulation duration) can be controlled from the Modeling dialog. }pMd/|A,  
[,)G\  
Steps  Description   NM{/r
vM  
1.  Launch the Modeling Dialog e: aa  
#oX8EMqs<  
In the Project Manager, choose [Model/Modeling...] to launch the Modeling dialog. Note the different modeling options for the project. See "Notes On Types of Excitation" below. v{[:7]b_=  
;"K;D@xzh]  
2.  Set the Type of Solution +-*Ww5Zti  
V6IC
R{y<3  
In the Modeling dialog, set: GWvw<`4  
Type of Solution to Internal Source(s) W#.+C6/  
^I CSs]}1  
The frequency range of interest: 8$TSQ~  
&xYO6_.  
Minimum Frequency Range = 700 MHz Glw_<ag[  
!
\6<kQg#  
Maximum Frequency Range = 1600 MHz }@XokRk  
"h'+!2mf  
For the total simulated time, i.e., the time after which the solver automatically stops, set:  e#t7
  
NlG~{rfI  
Max. Simulation Duration = 100 ns and make sure that the Terminal Resid. Energy = 0 W:gpcR]>  
`UK'IN.il  
# zbAA<f  
gZHuyp(B  
  Click [OK] to exit the Modeling dialog.  
dz>2/'  
~stJO])a  
=}D9sT  
Notes On Types of Excitation R ~ZcTY[8  
FLO/EMC can run three different types of simulations: fFYfb4
o  
l{o,"P"  
External Source: An external source (plane wave) radiates on the model. The plane wave is usually used to simulate an Electromagnetic source that is very far away from the model. The polarization and the direction of propagation can be controlled from the modeling menu. This type of source is usually used for immunity problems. rV_i|  
lPyY  
Internal Source(s): A voltage source will be used to excite the model. The voltage source it is usually placed inside the model for emissions problems. However, there is no restriction on the position of the sources. BH"Op
hE  
Pb
`Uxv  
Different of Excitation Types can be used in conjunction with the Internal Source(s). ?XIB\7}  
sW^e D;  
ouE/\4'NB  
!Soz??~o/  
The Broad band type, excite the model using a time domain pulse. The frequency response to this type of impulse is going flat over the frequency range of interest. In other words, the Broad band pulse excites each single frequency in the frequency range of interest with the same amplitude. }nUq=@ej  
The Direct excitation allows you to specify a custom transient waveform that FLO/EMC will use to excite the model. [`4  
The Indirect excitation runs the simulation using a Broad band pulse but at the end of the simulation, it will convolve the results using a user-defined transient. <%iRa$i5  
For more information about Broad band, Direct excitation and Indirect excitation, please refer to "Transient Excitation for an Internal Source(s) Solution". >_J9D?3S  
d2a*xDkv  
Coupling: One or more ports have to be specified inside the model. The S-parameters between those ports will then be calculated. }Be;YIhG  
77b^d9! ~  
The frequency range of interest and the Max simulation duration have to be carefully selected because are related to the computational resources required to run the simulation. Please refer to the training manual and to the on-line help to have more detailed information. 6Lc{SR  
On to 4: Introduction to the New Object Palette...

很多东西 说的很不清楚

恩，看它自带的帮助文档吧。

那多半还是你的安装方法不对，请参考dfmt版主的详细安装步骤

终于解决了安装问题，万幸啊

看看！多谢楼主！ b)<
WC$"  

在哪下载啊  我很想看看